Universal Device Driver Reference Manual

1.332 Irt-Pico-BUC

This page describes the device driver and the device window for the IRT Pico BUC Series via SNMP

The driver was tested with the following models:

10dBm Ka-Band Model - FW 2.11.3

Device window pages

The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .

--- The transmit parameters
--- Displays meter readings like output power and BUC specific measurements.
--- Displays the redundancy settings
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.

Configuration parameters

At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the unit.

parameter --- description
address --- The SNMP address specification for the device. The full address specification consists of the following fields:aaa.bbb.ccc.ddd:pppp read-community write-community
- aaa.bbb.ccc.ddd --- The IP address of the device in 'dotted quad' notation. This field is mandatory.
- pppp --- The IP port number where the device accepts SNMP requests. The port number may be omitted, the driver uses the standard port 161 in this case.
- read-community --- The SNMP read community name. This must match the read community expected by the device.
- write-community --- The SNMP write community name. This must match the write community expected by the device. The write community name may be omitted, the driver uses the read community name for both, read and write in this case. If both community names are missing, the driver uses 'public' as a default for read and write community.
powerDisplayMode --- Defines the display of gain or attenuation in the parameter section.
gainThreshold --- Defines a minimum gain threshold which raises an alarm when the measured gain falls below the threshold.

Variables defined by this device driver

name	type	flags	range
info.driver	TEXT	R/O	StringRange R/O
lowLevel.cmd	TEXT		StringRange
lowLevel.reply	TEXT	R/O	StringRange R/O
faults.99	ALARM	R/O	AlarmFlagRange R/O (Communication)
faults.commstat	TEXT	R/O	StringRange R/O
info.type	TEXT	R/O	StringRange R/O
info.port	TEXT	R/O	StringRange R/O
info.frame	TEXT	R/O	StringRange R/O
info.gainMin	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.gainMax	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.attnMin	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.attnMax	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.loFreq	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.freqMin	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.freqMax	INTEGER	R/O	IntegerRange R/O (0 .. 0)
info.signal.on	CHOICE	R/O	EnumRange R/O (OFF ON)
config.readBackDelay	INTEGER	SAVE SETUP	IntegerRange (100 .. 10000)
config.powerDisplayMode	CHOICE	SAVE SETUP	EnumRange (GAIN ATTN)
config.gainThreshold	FLOAT	SAVE SETUP	DoubleRange (0.0 .. 0.0)
tx.measuredLevel	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
rx.measuredLevel	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
tx.on	CHOICE		EnumRange (OFF ON)
tx.gain	FLOAT		DoubleRange (0.0 .. 0.0)
tx.attn	FLOAT		DoubleRange (0.0 .. 0.0)
tx.frequency	FLOAT		DoubleRange (0.000 .. 0.000)
meas.fwdPwr	INTEGER	R/O	IntegerRange R/O (0 .. 0)
meas.measuredLevel	FLOAT	R/O	DoubleRange R/O (0.000 .. 0.000)
meas.temperature	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
meas.gain	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
faults.01	ALARM	R/O	AlarmFlagRange R/O (PLL lock)
faults.02	ALARM	R/O	AlarmFlagRange R/O (Under current)
faults.03	ALARM	R/O	AlarmFlagRange R/O (Over temperature)
faults.04	ALARM	R/O	AlarmFlagRange R/O (Hardware)
faults.09	ALARM	R/O	AlarmFlagRange R/O (Low Gain)
faults.26	ALARM	R/O	AlarmFlagRange R/O (TX Off)