This page describes the device driver and the device window for the Newtec Azimuth AZ910 DVB-S2 Demodulator.
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- The IF parameters (frequency etc.) and some global settings.
--- The backup carrier configuration.
--- The demodulator settings.
--- The interface settings (eth, asi)
--- The receive status parameters including some interface statistics
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the Newtec EL470.
parameter --- description
address --- The SNMP address specification for the device. The full address specification consists of the following fields:aaa.bbb.ccc.ddd:pppp read-community write-community
rx.1.lnbPower --- Switches the LNB power for input 1 ON or OFF.
rx.1.lnbVoltge --- Selects voltage and 22kHz tone for input 1.
rx.1.spectrInv --- The LO spectrum invert for input 1. Set to NORM if the LO frequency is below the receive frequency, set to INVERT if the LO is above.
rx.2.lnbPower --- Switches the LNB power for input 2 ON or OFF.
rx.2.lnbVoltge --- Selects voltage and 22kHz tone for input 2.
rx.2.spectrInv --- The LO spectrum invert for input 2. Set to NORM if the LO frequency is below the receive frequency, set to INVERT if the LO is above.
loFreqHigh --- The LO frequency for the high frequency band. The software sets the appropriate LO frequency every time before it changes the receive frequency.
loFreqLow --- The LO frequency for the low frequency band. The software sets the appropriate LO frequency every time before it changes the receive frequency.
bandEdge --- The frequency where the software switches the LO frequencies.
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.3V3.supply | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.5V.supply | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.12V.supply | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.m12V.supply | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| config.rx.1.lnbPower | CHOICE | SETUP | EnumRange (OFF ON) |
| config.rx.1.lnbVoltage | CHOICE | SETUP | EnumRange (OFF 13V/0KHz 13V/22KHz 18V/0KHz 18V/22KHz) |
| config.rx.1.spectrInv | CHOICE | SETUP | EnumRange (NORM INVERT) |
| config.rx.2.lnbPower | CHOICE | SETUP | EnumRange (OFF ON) |
| config.rx.2.lnbVoltage | CHOICE | SETUP | EnumRange (OFF 13V/0KHz 13V/22KHz 18V/0KHz 18V/22KHz) |
| config.rx.2.spectrInv | CHOICE | SETUP | EnumRange (NORM INVERT) |
| config.loFreqHigh | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| config.loFreqLow | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| config.bandEdge | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| internal.dummy | TEXT | R/O | StringRange R/O |
| internal.lo | FLOAT | R/O | DoubleRange R/O (0 .. 0) |
| modemType | CHOICE | EnumRange (IP MPE: eth(ip)-air(ts) IP XPE/GSE: eth(ip)-air(s2bbf) DUALFLOW: eth(ip)/asi(ts)-air(s2bbf/ts) TSoIP: eth(tsoip)-asi(ts) ASI: asi(ts)-air(ts) ASI FIXED DELAY: asi(ts)-air(ts) ASI MULTISTREAM: asi(ts)-air(ts)) | |
| dvbMode | CHOICE | EnumRange (DVB-S DVB-S2) | |
| rx.input | CHOICE | EnumRange (IFL1 IFL2) | |
| rx.frequency | FLOAT | DoubleRange (0.000 .. 0.000) | |
| rx.dem.acmMode | CHOICE | EnumRange (CCM AUTO-CCM ACM) | |
| rx.dem.dataRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| rx.dem.symbolRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| rx.dem.acqRange | INTEGER | IntegerRange (1 .. 5000) | |
| rx.dem.isiControl | CHOICE | EnumRange (OFF ON) | |
| rx.dem.pidFiltering | CHOICE | EnumRange (OFF ON) | |
| rx.dem.plsSignature | INTEGER | IntegerRange (0 .. 262141) | |
| rx.dem.rollOff | CHOICE | EnumRange (AUTO 5% 10% 15% 20% 25% 35%) | |
| rx.dem.type | CHOICE | EnumRange (DUMMY-PL QPSK-NOFEC QPSK-1/2 QPSK-2/3 QPSK-3/4 QPSK-5/6 QPSK-6/7 QPSK-7/8 QPSK-AUTO QPSK-1/4 QPSK-1/3 QPSK-2/5 QPSK-3/5 QPSK-4/5 QPSK-8/9 QPSK-9/10 16APSK-2/3 16APSK-3/4 16APSK-4/5 16APSK-5/6 16APSK-8/9 16APSK-9/10 32APSK-3/4 32APSK-4/5 32APSK-5/6 32APSK-8/9 32APSK-9/10 16QAM-3/4 16QAM-7/8 16QAM-AUTO 8PSK-3/5 8PSK-2/3 8PSK-3/4 8PSK-AUTO 8PSK-5/6 8PSK-8/9 8PSK-9/10 AUTO) | |
| rx.dem.pilots | CHOICE | EnumRange (OFF ON) | |
| rx.dem.fecFrame | CHOICE | EnumRange (NORMAL SHORT) | |
| rx.backup.1.frequency | FLOAT | DoubleRange (0.000 .. 0.000) | |
| rx.backup.1.symbolRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| rx.backup.2.frequency | FLOAT | DoubleRange (0.000 .. 0.000) | |
| rx.backup.2.symbolRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| rx.backup.switchDelay | INTEGER | IntegerRange (10 .. 120) | |
| rx.backup.switchEnable | CHOICE | EnumRange (OFF ON) | |
| rx.backup.switchCount | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| eth.mtu | INTEGER | IntegerRange (1500 .. 2000) | |
| eth.l2Routing | CHOICE | EnumRange (OFF ON) | |
| eth.promiscuousMode | CHOICE | R/O | EnumRange R/O (OFF ON) |
| eth.forcePromiscuous | CHOICE | EnumRange (AUTOMATIC FORCE) | |
| asi.1.out.dvbs2Isi | TEXT | StringRange | |
| asi.1.out.mpegFraming | CHOICE | EnumRange (188 204 INTERNAL) | |
| asi.1.out.dataRate | FLOAT | DoubleRange (0.05500 .. 216.00000) | |
| asi.1.out.timingRecov | CHOICE | EnumRange (OFF ON ISSY) | |
| asi.1.out.signalSelect | CHOICE | EnumRange (OFF RXSIGNAL TESTGEN) | |
| asi.1.gen.type | CHOICE | EnumRange (PBRS COUNTER) | |
| asi.1.gen.pidInsert | CHOICE | EnumRange (OFF ON) | |
| asi.1.gen.pid | INTEGER | IntegerRange (0 .. 65535) | |
| asi.1.gen.dPackets | INTEGER | IntegerRange (1 .. 255) | |
| asi.1.gen.nPackets | INTEGER | IntegerRange (0 .. 255) | |
| asi.1.gen.outputRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| asi.2.out.dvbs2Isi | TEXT | StringRange | |
| asi.2.out.mpegFraming | CHOICE | EnumRange (188 204 INTERNAL) | |
| asi.2.out.dataRate | FLOAT | DoubleRange (0.05500 .. 216.00000) | |
| asi.2.out.timingRecov | CHOICE | EnumRange (OFF ON ISSY) | |
| asi.2.out.signalSelect | CHOICE | EnumRange (OFF RXSIGNAL TESTGEN) | |
| asi.2.gen.type | CHOICE | EnumRange (PBRS COUNTER) | |
| asi.2.gen.pidInsert | CHOICE | EnumRange (OFF ON) | |
| asi.2.gen.pid | INTEGER | IntegerRange (0 .. 65535) | |
| asi.2.gen.dPackets | INTEGER | IntegerRange (1 .. 255) | |
| asi.2.gen.nPackets | INTEGER | IntegerRange (0 .. 255) | |
| asi.2.gen.outputRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| rx.meter.level | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.ebno | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.esno | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.margin | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.type | TEXT | R/O | StringRange R/O |
| rx.meter.frameType | TEXT | R/O | StringRange R/O |
| rx.meter.pilots | TEXT | R/O | StringRange R/O |
| rx.meter.rollOff | TEXT | R/O | StringRange R/O |
| rx.meter.isiFilterByte | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.meter.bbDataFieldLength | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.flags.lock | BOOLEAN | R/O | BooleanRange R/O (true false) |
| rx.ifc.pidFilterMode | CHOICE | EnumRange (OFF ON) | |
| rx.ifc.pidFilterCode | INTEGER | IntegerRange (0 .. 8191) | |
| rx.ifc.pbrsStatus | TEXT | R/O | StringRange R/O |
| rx.ifc.errorCount | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.ifc.pbrsSyncSeconds | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.ifc.errorRate | FLOAT | R/O | DoubleRange R/O (0.00E+00 .. 0.00E+00) |
| rx.ifc.errorRatio | FLOAT | R/O | DoubleRange R/O (0.00E+00 .. 0.00E+00) |
| rx.ifc.pbrsMonitorInput | CHOICE | EnumRange (OFF ASI1 RX ASI1 TX ASI2 RX ASI2 TX ASI3 RX ASI3 TX) | |
| ethIfcAState | TEXT | R/O | StringRange R/O |
| ethIfcBState | TEXT | R/O | StringRange R/O |
| eth.errorPackets | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| eth.packets | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| eth.resetCounters | CHOICE | NOCOMPARE | EnumRange (PERIOD NEVER ONCE) |
| rx.bb.txTsFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.rxTsFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.rxDroppedFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.tsCrc8Errors | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.bbfCrc8Errors | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.resetCounters | CHOICE | NOCOMPARE | EnumRange (PERIOD NEVER ONCE) |
| rx.bb.rxRawBitrate | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.rxRawFramerate | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.1.droppedFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.2.droppedFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.bb.3.droppedFrames | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Device reset flag) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Self test) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Incompatibility) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (General device) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Interface) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Reference clock) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Device temperature) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Power supply voltage) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Eth IfA Link) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Eth IfB Link) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Eth IfA half duplex) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Eth IfB half duplex) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (IP GW unreachable) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (Eth Ifc switchover) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (ASI Rx 1 Input) |
| faults.16 | ALARM | R/O | AlarmFlagRange R/O (ASI Rx 2 Input) |
| faults.17 | ALARM | R/O | AlarmFlagRange R/O (ASI Ifc switchover) |
| faults.18 | ALARM | R/O | AlarmFlagRange R/O (Demod Rx bad packet) |
| faults.19 | ALARM | R/O | AlarmFlagRange R/O (Demod Rx buf oflow) |
| faults.20 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 1 buf uflow) |
| faults.21 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 2 buf uflow) |
| faults.22 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 3 buf uflow) |
| faults.23 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 4 buf uflow) |
| faults.24 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 1 buf oflow) |
| faults.25 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 2 buf oflow) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 3 buf oflow) |
| faults.27 | ALARM | R/O | AlarmFlagRange R/O (ASI Tx 4 buf oflow) |
| faults.28 | ALARM | R/O | AlarmFlagRange R/O (ASI Rx 1 buf oflow) |
| faults.29 | ALARM | R/O | AlarmFlagRange R/O (ASI Rx 2 buf oflow) |
| faults.30 | ALARM | R/O | AlarmFlagRange R/O (Demod lock) |
| faults.31 | ALARM | R/O | AlarmFlagRange R/O (Demod tuner lock) |
| faults.32 | ALARM | R/O | AlarmFlagRange R/O (Demod PL sync) |
| faults.33 | ALARM | R/O | AlarmFlagRange R/O (Demod BB sync) |
| faults.34 | ALARM | R/O | AlarmFlagRange R/O (Internal M&C module) |
| faults.35 | ALARM | R/O | AlarmFlagRange R/O (Interface module) |
| faults.36 | ALARM | R/O | AlarmFlagRange R/O (Demodulator module) |
| faults.37 | ALARM | R/O | AlarmFlagRange R/O (Device architecture) |
| faults.38 | ALARM | R/O | AlarmFlagRange R/O (Internal communication) |
| faults.39 | ALARM | R/O | AlarmFlagRange R/O (Level saturation) |