This page describes the device driver and the device window for the Newtec MDM6100 DVB-S2 Modulator and Demodulator.
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- The IF parameters (frequency, level, etc.) and some global settings.
--- The modulator settings.
--- The demodulator settings.
--- The TX interface settings.
--- The RX interface settings.
--- The transport stream multiplexer settings.
--- Shows statistical values, error rates etc.
--- The transport stream analyzer page
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the MDM6100.
| parameter | description |
|---|---|
| address | The SNMP address specification for the device. The full address specification consists of the following fields:aaa.bbb.ccc.ddd:pppp read-community write-community |
| aaa.bbb.ccc.ddd | The IP address of the device in 'dotted quad' notation. This field is mandatory. |
| pppp | The IP port number where the device accepts SNMP requests. The port number may be omitted, the driver uses the standard port 161 in this case. |
| read-community | The SNMP read community name. This must match the read community expected by the device. |
| write-community | The SNMP write community name. This must match the write community expected by the device. The write community name may be omitted, the driver uses the read community name for both, read and write in this case. If both community names are missing, the driver uses 'public' as a default for read and write community. |
| ratePriority | Selects if the modultor shall keep the symbol rate or the interface rate constant if e.g. modulation or fec rate is changed. |
| extLoFreq | The LO frequency of an external upconverter. |
| extLoPolarity | With NRM the driver assumes an LO frequency below the RF transmit frequency. With INV the LO frequency is assumed above the RF frequency. |
| output10MHz | Selects if a 10MHz reference clock shall be present at the L-Band output. |
| onDeviceAlarm | Specifies what to do on device alarms (IGNORE / TX-OFF) |
| minOutputLevel | Defines the minimum tx output power level (dBm) of the modulator as this cannot be read from the unit |
| maxOutputLevel | Defines the maximum tx output power level (dBm) of the modulator as this cannot be read from the unit |
| readBackDelay | Defines the delay the driver uses when it reads back parameters recently commanded. The delay is initialized at a proved preset value which should not be changed under normal circumstances |
| rx.reference | Defines 10Mhz Reference signal |
| rx.lnbPower | Selects if the Demodulator shall apply LNB power to the input |
| rx.lnbVoltage | Selects the LNB power supply voltage (13V/18V). This switches the polarization (13V=Vertical) with some LNBs |
| rx.lnbTone | Makes the Demodulator apply a 22 kHz tone to the LNB power when set to ON. |
| rx.marginThreshold | Defines the minimum s/n margin value the driver accepts as OK. s/n margin values below this threshold raise an "Margin" fault (faults.30). The margin fault detection is done by the sat-nms device driver, not by the device itself. Hence, the margin value ist stored as a saved parameter on the VLC rather than as a parameter in the IRD. |
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.hwID | TEXT | R/O | StringRange R/O |
| info.hwRevision | TEXT | R/O | StringRange R/O |
| info.swID | TEXT | R/O | StringRange R/O |
| info.swRevision | TEXT | R/O | StringRange R/O |
| info.serialNo | TEXT | R/O | StringRange R/O |
| info.internalTemp | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.pwrSupply | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| config.ratePriority | CHOICE | SETUP | EnumRange (SYMBOL INTERFACE) |
| config.extLoFreq | FLOAT | SAVE SETUP | DoubleRange (0.0 .. 0.0) |
| config.extLoPolarity | CHOICE | SAVE SETUP | EnumRange (NRM INV) |
| config.output10Mhz | CHOICE | SETUP | EnumRange (OFF ON) |
| config.onDeviceAlarm | CHOICE | SETUP | EnumRange (IGNORE TX OFF) |
| config.onIfcAlarm | CHOICE | SETUP | EnumRange (IGNORE TX OFF) |
| config.minOutputLevel | FLOAT | SAVE SETUP | DoubleRange (0.0 .. 0.0) |
| config.maxOutputLevel | FLOAT | SAVE SETUP | DoubleRange (0.0 .. 0.0) |
| config.readBackDelay | INTEGER | IntegerRange (0 .. 0) | |
| config.rx.loFreqHigh | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| config.rx.loFreqLow | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| config.rx.bandEdge | INTEGER | SAVE SETUP | IntegerRange (0 .. 0) |
| config.rx.reference | CHOICE | SETUP | EnumRange (ON OFF) |
| config.rx.lnbPower | CHOICE | SETUP | EnumRange (OFF ON) |
| config.rx.lnbVoltage | CHOICE | SETUP | EnumRange (OFF 13V 18V) |
| config.rx.lnbTone | CHOICE | SETUP | EnumRange (OFF ON) |
| config.marginThreshold | FLOAT | SAVE SETUP | DoubleRange (0.0 .. 0.0) |
| refClkSrc | CHOICE | EnumRange (INTERN EXTERN) | |
| refClkFreq | CHOICE | EnumRange (1 MHz 2 MHz 5 MHz 10 MHz 20 MHz) | |
| saveBootConfig | TEXT | NOPRESET | StringRange |
| unsavedChanges | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tx.dvbMode | CHOICE | EnumRange (DVBS DVBS2) | |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.frequency | FLOAT | DoubleRange (0.0000 .. 0.0000) | |
| tx.power | FLOAT | DoubleRange (-35.0 .. 10.0) | |
| tx.mod.rollOff | CHOICE | EnumRange (5% 10% 15% 20% 25% 35%) | |
| tx.mod.occupiedBw | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| tx.mod.measuredRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tx.mod.spectrumInvert | CHOICE | EnumRange (NRM INV) | |
| tx.mod.cwMode | CHOICE | EnumRange (CW MOD CLK/8 CLK/4 CLK/16) | |
| tx.mod.amplitudeEQ | INTEGER | IntegerRange (-7 .. 7) | |
| tx.mod.dataRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| tx.mod.symbolRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| tx.mod.type | CHOICE | EnumRange (QPSK-1/4 QPSK-1/3 QPSK-2/5 QPSK-1/2 QPSK-3/5 QPSK-2/3 QPSK-3/4 QPSK-4/5 QPSK-5/6 QPSK-8/9 QPSK-9/10 8PSK-3/5 8PSK-2/3 8PSK-3/4 8PSK-5/6 8PSK-8/9 8PSK-9/10 16APSK-2/3 16APSK-3/4 16APSK-4/5 16APSK-5/6 16APSK-8/9 16APSK-9/10 32APSK-3/4 32APSK-4/5 32APSK-5/6 32APSK-8/9 32APSK-9/10) | |
| tx.mod.modcod | CHOICE | EnumRange (QPSK-1/4 QPSK-1/3 QPSK-2/5 QPSK-1/2 QPSK-3/5 QPSK-2/3 QPSK-3/4 QPSK-4/5 QPSK-6/7 QPSK-7/8 QPSK-5/6 QPSK-8/9 QPSK-9/10 8PSK-3/5 8PSK-2/3 8PSK-3/4 8PSK-5/6 8PSK-8/9 8PSK-9/10 16QAM-3/4 16QAM-7/8 16APSK-2/3 16APSK-3/4 16APSK-4/5 16APSK-5/6 16APSK-8/9 16APSK-9/10 32APSK-3/4 32APSK-4/5 32APSK-5/6 32APSK-8/9 32APSK-9/10) | |
| tx.mod.fec | CHOICE | EnumRange (1/2 1/3 1/4 2/3 2/5 3/4 3/5 4/5 5/6 8/9 9/10) | |
| tx.mod.modulation | CHOICE | EnumRange (QPSK 8PSK 16QAM 16APSK 32APSK) | |
| tx.mod.fecFrameType | CHOICE | EnumRange (SHORT NORMAL) | |
| tx.mod.insertPilots | CHOICE | EnumRange (ON OFF) | |
| tx.mod.isi | INTEGER | IntegerRange (0 .. 255) | |
| tx.mod.input | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tx.asi.in.inputSelect | CHOICE | EnumRange (NONE ASI 1 ASI 2 ASI 1 OR 2 ASI 1 BEFORE 2 ASI 2 BEFORE 1 PBRS GENERATOR) | |
| protection | CHOICE | R/O | EnumRange R/O (OFF ON) |
| tx.asi.in.activeInput | CHOICE | R/O | EnumRange R/O (OFF ASI 1 ASI 2) |
| tx.asi.in.position | CHOICE | R/O | EnumRange R/O (A B NONE) |
| tx.asi.in.inlineSplit | CHOICE | EnumRange (NONE 3DB SPLIT 6DB SPLIT) | |
| tx.asi.in.measuredRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| tx.asi.in.inputFraming | CHOICE | EnumRange (TS 188 TS 204) | |
| tx.asi.in.itfSwitchCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.asi.in.pbrsRate | FLOAT | DoubleRange (0.000000 .. 0.000000) | |
| tx.asi.in.pbrsType | CHOICE | EnumRange (PBRS COUNTER) | |
| tx.asi.in.pbrsPid | CHOICE | EnumRange (OFF ON) | |
| tx.asi.in.pbrsPidVal | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.in.pbrsDPackets | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.in.pbrsNPackets | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.out.signalSelect | CHOICE | EnumRange (NONE MODULATOR INPUT ACTIVE INPUT NONACTIVE INPUT DEMODULATOR OUTPUT PBRS GENERATOR) | |
| tx.asi.out.outputSelect | CHOICE | EnumRange (NONE ASI 3 ASI 4 ASI 3 AND 4) | |
| tx.asi.out.measuredRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| tx.asi.out.pbrsRate | FLOAT | DoubleRange (0.000000 .. 0.000000) | |
| tx.asi.out.pbrsType | CHOICE | EnumRange (PBRS COUNTER) | |
| tx.asi.out.pbrsPid | CHOICE | EnumRange (OFF ON) | |
| tx.asi.out.pbrsPidVal | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.out.pbrsDPackets | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.out.pbrsNPackets | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.mon.enable | CHOICE | EnumRange (OFF ON) | |
| tx.asi.mon.pid | CHOICE | EnumRange (OFF ON) | |
| tx.asi.mon.pidVal | INTEGER | IntegerRange (0 .. 0) | |
| tx.asi.mon.state | TEXT | R/O | StringRange R/O |
| tx.asi.mon.syncSecs | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.asi.mon.errorCount | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.asi.mon.errorRate | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| tx.tsoip.enable | CHOICE | EnumRange (OFF ON) | |
| tx.tsoip.inputSelect | CHOICE | EnumRange (NONE DATA 1 DATA 2 DATA) | |
| tx.tsoip.encapProtocol | CHOICE | EnumRange (UDP RTP RTP WITH FEC) | |
| tx.tsoip.addressType | CHOICE | EnumRange (UNICAST MULTICAST) | |
| tx.tsoip.mcastAddress | TEXT | StringRange | |
| tx.tsoip.udpPort | INTEGER | IntegerRange (0 .. 0) | |
| tx.tsoip.trafficProfile | CHOICE | EnumRange (VBR CBR) | |
| tx.tsoip.maxTrafJitter | INTEGER | IntegerRange (0 .. 0) | |
| tx.tsoip.maxBuffDelay | INTEGER | IntegerRange (0 .. 0) | |
| tx.tsoip.dataRate | FLOAT | DoubleRange (0.000000 .. 0.000000) | |
| tx.tsoip.reset | TEXT | StringRange | |
| tx.tsoip.mon.dataRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| tx.tsoip.mon.buffDelay | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.maxBuffFill | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.minBuffFill | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.tsInCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.tsDropCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.tsOFlwCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.rtpInCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.rtpDropCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.tsoip.mon.rtpRepairCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| tx.mux.input.1.name | TEXT | R/O | StringRange R/O |
| tx.mux.input.1.enable | CHOICE | EnumRange (OFF ON) | |
| tx.mux.input.2.name | TEXT | R/O | StringRange R/O |
| tx.mux.input.2.enable | CHOICE | EnumRange (OFF ON) | |
| tx.mux.ra.enable | CHOICE | EnumRange (OFF ON) | |
| tx.mux.ra.nullpDrop | CHOICE | EnumRange (OFF ON) | |
| tx.mux.ra.pcrRestamp | CHOICE | EnumRange (OFF ON) | |
| tx.mux.sig.networkId | INTEGER | IntegerRange (0 .. 0) | |
| tx.mux.sig.tsId | INTEGER | IntegerRange (0 .. 0) | |
| tx.mux.sig.patRepRate | INTEGER | IntegerRange (0 .. 0) | |
| tx.mux.sig.sdtRepRate | INTEGER | IntegerRange (0 .. 0) | |
| tx.mux.cid.enable | CHOICE | EnumRange (OFF ON) | |
| tx.mux.cid.descrTag | INTEGER | IntegerRange (0 .. 0) | |
| tx.mux.cid.carrierId | TEXT | StringRange | |
| tx.mux.cid.telnNo | TEXT | StringRange | |
| tx.mux.cid.userInfo | TEXT | StringRange | |
| tsanalyzer.enable | CHOICE | EnumRange (OFF ON) | |
| tsanalyzer.reset | TEXT | StringRange | |
| tsanalyzer.estimatedRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| tsanalyzer.pidList | TEXT | R/O | StringRange R/O |
| tsanalyzer.1.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.1.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.1.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.1.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.1.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.2.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.2.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.2.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.2.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.2.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.3.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.3.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.3.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.3.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.3.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.4.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.4.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.4.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.4.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.4.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.5.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.5.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.5.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.5.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.5.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.6.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.6.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.6.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.6.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.6.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.7.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.7.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.7.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.7.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.7.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.8.enable | CHOICE | SAVE | EnumRange (OFF ON) |
| tsanalyzer.8.pid | INTEGER | SAVE | IntegerRange (0 .. 0) |
| tsanalyzer.8.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| tsanalyzer.8.continuityErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| tsanalyzer.8.transportErr | BOOLEAN | R/O | BooleanRange R/O (true false) |
| reset | TEXT | NOPRESET | StringRange |
| rx.on | CHOICE | EnumRange (ON OFF) | |
| rx.dem.dvbMode | CHOICE | EnumRange (DVBS DVBS2 DVBS2X TURBO AMC-DVBS AMC-NBC AMC-DL DVBS2EXT) | |
| rx.frequency | FLOAT | DoubleRange (0.000 .. 0.000) | |
| rx.dem.symbolRate | FLOAT | DoubleRange (0.00000 .. 0.00000) | |
| rx.dem.rollOff | CHOICE | EnumRange (AUTO 5% 10% 15% 20% 25% 35%) | |
| rx.input | CHOICE | EnumRange (RX-A RX-B IF) | |
| rx.dem.spectrumInvert | CHOICE | EnumRange (AUTO NORMAL INVERT) | |
| rx.dem.plsSignature | INTEGER | IntegerRange (0 .. 262141) | |
| rx.dem.type | CHOICE | EnumRange (DUMMY-PL QPSK-NOFEC QPSK-1/2 QPSK-2/3 QPSK-3/4 QPSK-5/6 QPSK-6/7 QPSK-7/8 QPSK-AUTO QPSK-1/4 QPSK-1/3 QPSK-2/5 QPSK-3/5 QPSK-4/5 QPSK-8/9 QPSK-9/10 16APSK-2/3 16APSK-3/4 16APSK-4/5 16APSK-5/6 16APSK-8/9 16APSK-9/10 32APSK-3/4 32APSK-4/5 32APSK-5/6 32APSK-8/9 32APSK-9/10 16QAM-3/4 16QAM-7/8 16QAM-AUTO 8PSK-3/5 8PSK-2/3 8PSK-3/4 8PSK-AUTO 8PSK-5/6 8PSK-8/9 8PSK-9/10 AUTO) | |
| rx.dem.streamMode | CHOICE | EnumRange (SINGLE MULTI) | |
| rx.dem.dataRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| rx.dem.acqRange | INTEGER | IntegerRange (1 .. 5000) | |
| rx.dem.plsKey | INTEGER | IntegerRange (0 .. 2000) | |
| rx.dem.transponderMode | CHOICE | EnumRange (SCPC NON LINEAR MCPC SCPC LINEAR) | |
| rx.flags.lock | BOOLEAN | R/O | BooleanRange R/O (true false) |
| rx.meter.level | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.carrierLevel | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.margin | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.frequencyOffset | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| rx.meter.symbolRate | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| rx.meter.esno | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| rx.meter.rollOff | TEXT | R/O | StringRange R/O |
| rx.meter.modcod | TEXT | R/O | StringRange R/O |
| rx.meter.frameType | TEXT | R/O | StringRange R/O |
| rx.meter.pilots | TEXT | R/O | StringRange R/O |
| rx.tsoip.enable | CHOICE | EnumRange (OFF ON) | |
| rx.tsoip.protocol | CHOICE | EnumRange (UDP RTP RTP COLS ONLY RTP COLS AND ROWS) | |
| rx.tsoip.port | INTEGER | IntegerRange (1 .. 65535) | |
| rx.tsoip.address | TEXT | StringRange | |
| rx.tsoip.ttl | INTEGER | IntegerRange (1 .. 255) | |
| rx.tsoip.packetsFrame | INTEGER | IntegerRange (1 .. 7) | |
| rx.tsoip.fecColumns | INTEGER | IntegerRange (0 .. 0) | |
| rx.tsoip.fecRows | INTEGER | IntegerRange (0 .. 0) | |
| rx.tsoip.schedule | INTEGER | IntegerRange (500 .. 5000) | |
| rx.tsoip.mon.dataRate | FLOAT | R/O | DoubleRange R/O (0.000000 .. 0.000000) |
| rx.tsoip.mon.tsDropCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.tsoip.mon.tsOFlwCnt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| rx.tsoip.reset | TEXT | NOPRESET | StringRange |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Device general) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Interface general) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (ASI general) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (ASI input signal) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (ASI input data) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (ASI buffer oflow) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (TSoIP general) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (TSoIP input data) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (TSoIP buffer oflow) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (TSoIP buffer uflow) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Mod general) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Mod input signal) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Mod buffer oflow) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (Mod buffer uflow) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (Mod synth) |
| faults.16 | ALARM | R/O | AlarmFlagRange R/O (Mod ref synth lock) |
| faults.17 | ALARM | R/O | AlarmFlagRange R/O (Mod lo1 lock) |
| faults.18 | ALARM | R/O | AlarmFlagRange R/O (Mod lo2 lock) |
| faults.19 | ALARM | R/O | AlarmFlagRange R/O (TA ts sync) |
| faults.20 | ALARM | R/O | AlarmFlagRange R/O (TA ts sync byte) |
| faults.21 | ALARM | R/O | AlarmFlagRange R/O (TA ts pat) |
| faults.22 | ALARM | R/O | AlarmFlagRange R/O (TA ts continuity) |
| faults.23 | ALARM | R/O | AlarmFlagRange R/O (TA ts pcr repetition) |
| faults.24 | ALARM | R/O | AlarmFlagRange R/O (TA ts pcr continuity) |
| faults.25 | ALARM | R/O | AlarmFlagRange R/O (TA ts pcr accuracy) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (Demod general) |
| faults.27 | ALARM | R/O | AlarmFlagRange R/O (Demod internal) |
| faults.28 | ALARM | R/O | AlarmFlagRange R/O (Demod input saturated) |
| faults.29 | ALARM | R/O | AlarmFlagRange R/O (Demod pl lock) |
| faults.31 | ALARM | R/O | AlarmFlagRange R/O (Demod lock) |
| faults.32 | ALARM | R/O | AlarmFlagRange R/O (Demod lnb supply) |
| faults.33 | ALARM | R/O | AlarmFlagRange R/O (Demod overload) |
| faults.34 | ALARM | R/O | AlarmFlagRange R/O (TSoIP Output) |
| faults.35 | ALARM | R/O | AlarmFlagRange R/O (TSoIP Output Overflow) |
| faults.30 | ALARM | R/O | AlarmFlagRange R/O (Margin) |
| internal.dvbMode | TEXT | R/O | StringRange R/O |
| internal.freq | FLOAT | R/O | DoubleRange R/O (0.00000 .. 0.00000) |
| internal.tx.on | TEXT | R/O | StringRange R/O |
| internal.type | TEXT | R/O | StringRange R/O |
| internal.lo | FLOAT | R/O | DoubleRange R/O (0 .. 0) |