--- Switch parameters.
--- Switch readings.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for a Novotronik LNA Switching Unit GTS6300.
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- Switch parameters. --- Switch readings. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
The GTS6300 do not need any configuration parameters except the settings for the serial interface. The default address is 0.
| parameter | description |
|---|---|
| Serial | Remember to set the line parameters for the serial interface connected to the device. The recommended line setting for the use with the sat-nms software is 9600,N,7,1 . |
| readBackDelay | Defines the delay the driver uses when it reads back parameters recently commanded. The delay is initialized at a proved preset value which should not be changed under normal circumstances. |
| config.controlMode | Switches the device control mode between local and remote. |
| config.dcPs1 | Switches DC power supply 1. |
| config.dcPs2 | Switches DC power supply 2. |
| config.dcPs3 | Switches DC power supply 3. |
Remote Control
RS485/422 uses Novotronik-ASCII protocol
RS232 uses Novotronik protocol
TCP uses Terminal LF protocol
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| config.controlMode | CHOICE | SETUP | EnumRange (LOCAL REMOTE) |
| config.dcPs1 | CHOICE | SETUP | EnumRange (OFF ON) |
| config.dcPs2 | CHOICE | SETUP | EnumRange (OFF ON) |
| config.dcPs3 | CHOICE | SETUP | EnumRange (OFF ON) |
| position | CHOICE | EnumRange (3-STBY 1-STBY 2-STBY) | |
| position.1 | CHOICE | EnumRange (A B) | |
| position.2 | CHOICE | EnumRange (A B) | |
| priority | CHOICE | EnumRange (NONE PATH-1 PATH-2) | |
| protection | CHOICE | EnumRange (MANUAL AUTO) | |
| info.swVersion | TEXT | R/O | StringRange R/O |
| info.swDate | TEXT | R/O | StringRange R/O |
| info.serialNo | TEXT | R/O | StringRange R/O |
| info.model | TEXT | R/O | StringRange R/O |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (DC voltage 1) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (DC voltage 2) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (DC voltage 3) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Temperature) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Control/Switch board) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Voltage control board) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Switch 1) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Switch 2) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Switch 3) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Switch 4) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 1) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 2) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 3 (spare)) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (Remote Access) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (PSU 1) |
| faults.16 | ALARM | R/O | AlarmFlagRange R/O (PSU 2) |
| faults.17 | ALARM | R/O | AlarmFlagRange R/O (COM PSU 1/2) |
| faults.18 | ALARM | R/O | AlarmFlagRange R/O (Protection) |