--- Port switching.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for a Novotronik Switching Unit GTS6821
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- Port switching. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
The GTS6821 do not need any configuration parameters except the settings for the serial interface
| parameter | description |
|---|---|
| Serial | Remember to set the line parameters for the serial interface connected to the device. The recommended line setting for the use with the sat-nms software is 9600,N,8,1 . |
| readBackDelay | Defines the delay the driver uses when it reads back parameters recently commanded. The delay is initialized at a proved preset value which should not be changed under normal circumstances. |
Remote Control
RS485/422 uses Novotronik-ASCII protocol
RS232 uses Novotronik protocol
TCP uses Terminal LF protocol
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| position.10 | CHOICE | EnumRange (A B) | |
| position.11 | CHOICE | EnumRange (A B) | |
| position.12 | CHOICE | EnumRange (A B) | |
| position.13 | CHOICE | EnumRange (A B) | |
| position.14 | CHOICE | EnumRange (A B) | |
| position.15 | CHOICE | EnumRange (A B) | |
| wgstat.10 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgstat.11 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgstat.12 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgstat.13 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgstat.14 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgstat.15 | HEX | R/O | HexRange R/O (0 .. 0) |
| wgcmd.10 | HEX | HexRange (0 .. 0) | |
| wgcmd.11 | HEX | HexRange (0 .. 0) | |
| wgcmd.12 | HEX | HexRange (0 .. 0) | |
| wgcmd.13 | HEX | HexRange (0 .. 0) | |
| wgcmd.14 | HEX | HexRange (0 .. 0) | |
| wgcmd.15 | HEX | HexRange (0 .. 0) | |
| info.swVersion | TEXT | R/O | StringRange R/O |
| info.swDate | TEXT | R/O | StringRange R/O |
| info.serialNo | TEXT | R/O | StringRange R/O |
| info.model | TEXT | R/O | StringRange R/O |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Power supply 1) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Power supply 2) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Internal voltage) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Temperature) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Switch ctrl board) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Switch S10) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Switch S11) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Switch S12) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Switch S13) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Switch S14) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Switch S15) |
| initialized | TEXT | R/O | StringRange R/O |