--- The operational upconverter parameters
--- Meter readings
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for the Paradise indoor SSPA amplifier 2200AM. It was tested with:
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- The operational upconverter parameters --- Meter readings --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the SSPA.
| parameter | description |
|---|---|
| address | The device IP address and the SNMP community strings as set at the device's front panel. |
| powerDisplayMode | Select if you want to see gain or attenuation |
| sysMode | Allows to select the system configuration. |
| standbyMode | Allows to select the standby mode in a redundant configuration. |
| powerSupplies | Defines the number of power supplies to be monitored |
| hasRefPwrSensor | Defines if the unit is equipped with a reflected power measurement sesnor. |
| gainMode | Sets the units gain mode |
| hpaNumber | Sets the HPA number |
Communication protocol / Interface type
This device driver requires the SNMP protocol. Please remember to configure the ip settings (Main Menu - 2.Com Setup) and enable SNMP at the front panel
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.serial | TEXT | R/O | StringRange R/O |
| info.model | TEXT | R/O | StringRange R/O |
| info.revision | TEXT | R/O | StringRange R/O |
| info.deviceType | TEXT | R/O | StringRange R/O |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| config.sysMode | CHOICE | SETUP | EnumRange (StandAlone 1:1 Dual-1:1 MaintenanceSwitch) |
| config.standbyMode | CHOICE | SETUP | EnumRange (HotStandby ColdStandby) |
| config.powerSupplies | CHOICE | SAVE SETUP | EnumRange (1 2) |
| config.hasRefPwrSensor | CHOICE | SAVE SETUP | EnumRange (YES NO) |
| config.gainMode | CHOICE | SETUP | EnumRange (MANUAL ALC VOLTAGE) |
| config.hpaNumber | CHOICE | SETUP | EnumRange (HPA-1 HPA-2) |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.gain | FLOAT | DoubleRange (0.0 .. 20.0) | |
| tx.attn | FLOAT | DoubleRange (0.0 .. 20.0) | |
| tx.requestedLevel | FLOAT | DoubleRange (0.0 .. 80.0) | |
| tx.measuredLevel | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| tx.measuredLevel2 | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.fwdPwr | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| meas.refPwr | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.current | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.ps1Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.ps2Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.regulator1Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.regulator2Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.gate1Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.gate2Voltage | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.temp | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| red.mode | CHOICE | EnumRange DIS (AUTO MANUAL) | |
| red.switch | CHOICE | EnumRange DIS (STANDBY ONLINE) | |
| position | CHOICE | EnumRange DIS (A B) | |
| internal.fwd | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| internal.ref | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| internal.flt | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| internal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Summary) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (High temp) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Low DC current) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Low DC regulator voltage) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Ext Mute) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Int Mute) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Forward RF) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Reflected RF) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (BUC) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Spare) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Auxiliary) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Switch position 1) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Switch position 2) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (Standby) |