--- Switch parameters
--- The faults page.
--- The device info page.
--- The maintenance page.This page describes the device driver and the device window for the Symmetricom 2x12 Distribution Unit Type 9611B
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- Switch parameters --- The faults page. --- The device info page. --- The maintenance page.Configuration parameters
The Symmetricom device needs some configuration parameters as well as the correct settings for the serial interface
| parameter | description |
|---|---|
| Serial | Remember to set the line parameters for the serial interface connected to the device. The recommended line setting for the use with the sat-nms software is 115200,N,8,1 . |
| impedance | Define if 50Ohm or 1kOhm impedance should be used. |
Remote Control
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| config.impedance | CHOICE | SETUP | EnumRange (50 Ohm 1000 Ohm) |
| info.model | TEXT | R/O | StringRange R/O |
| info.versionMicro | TEXT | R/O | StringRange R/O |
| info.versionFpga | TEXT | R/O | StringRange R/O |
| input | CHOICE | EnumRange (1Hz to < 10Hz 10Hz to < 100Hz 100Hz to < 1kHz 1kHz to < 10kHz 10kHz to < 100kHz 100kHz and above Digital IRIG A Digital IRIG B Digital IRIG D Digital IRIG E Digital IRIG G Digital IRIG H AM IRIG - 100Hz carrier AM IRIG - 1kHz carrier AM IRIG - 10kHz carrier) | |
| position | CHOICE | EnumRange (A B) | |
| protection | CHOICE | EnumRange (AUTO USER) | |
| internal.faultList | TEXT | R/O | StringRange R/O |
| int.fault1 | TEXT | R/O | StringRange R/O |
| int.fault2 | TEXT | R/O | StringRange R/O |
| internal.position | TEXT | R/O | StringRange R/O |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Input 1) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Input 2) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Output 01) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Output 02) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Output 03) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Output 04) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Output 05) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Output 06) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Output 07) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Output 08) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (Output 09) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Output 10) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Output 11) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (Output 12) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (Protection) |