--- The transmit parameters
--- The meter readings.
--- The redundancy parameters.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for the Work Amplifier series
The driver was tested with the following models:
Device window pages
The following table shows which device window pages are available with this individual device type.
--- The transmit parameters --- The meter readings. --- The redundancy parameters. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the unit.
| parameter | description |
|---|---|
| address | The device address (decimal) as set at the device's front panel. |
| Serial | Remember to set the line parameters for the serial interface |
| powerDisplayMode | Defines the display of gain or attenuation in the parameter section. |
| extMuteInput | Defines to disable or enable the input for Hardware Mute (RF-Inhibit). |
| autoSave | Store current parameters automatically in the instrument startup configuration. |
Remote Control
Default TCP Port = 50505
Default Address = A
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.serial | TEXT | R/O | StringRange R/O |
| info.FrontBaseVersion | TEXT | R/O | StringRange R/O |
| info.FrontDeviceVersion | TEXT | R/O | StringRange R/O |
| info.InterfaceVersion | TEXT | R/O | StringRange R/O |
| info.AmpModuleVersion | TEXT | R/O | StringRange R/O |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| config.extMuteInput | CHOICE | SETUP | EnumRange (ENABLED DISABLED) |
| config.autoSave | CHOICE | SETUP | EnumRange (OFF ON) |
| on | CHOICE | EnumRange (OFF ON) | |
| gain | FLOAT | DoubleRange (0.0 .. 20.0) | |
| attn | FLOAT | DoubleRange (0.0 .. 20.0) | |
| eq | FLOAT | DoubleRange (0.0 .. 8.0) | |
| meas.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.temp.frontpanel | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.temp.controller | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| reset | TEXT | NOPRESET | StringRange |
| internal.sa0 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| internal.sa1 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Remote access) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Amplifier module) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Internal module) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Module comm.) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Ext. Mute) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Temp. Sensor) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Key) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Real time clock) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Display) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (Ethernet) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (EEPROM) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (High temperature) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Low temperature) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (Webserver) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (Webcontrol) |
| faults.16 | ALARM | R/O | AlarmFlagRange R/O (Message bus) |
| faults.17 | ALARM | R/O | AlarmFlagRange R/O (Summary) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (RF Off) |