--- Parameters.
--- The faults page.
--- The device info page.
--- The maintenance page.This page describes the device driver and the device window for etl systems splitter card DIV 409.
Together with a etl system 26128 frame each DIV 409 card has to be addressed individually.
To allow proper operation the slot number and device address has to be defined in the configuration page.
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- Parameters. --- The faults page. --- The device info page. --- The maintenance page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the device.
| parameter | description |
|---|---|
| address | Must always be set to B if the device is controlled TCP or over a serial line. |
| readBackDelay | Defines the delay the driver uses when it reads back parameters recently commanded. The delay is initialized or a proved preset value which should not be changed under normal circumstances. |
| slot | Defines the slot number of the respective module. This is necessary for proper communication. |
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.model | TEXT | R/O | StringRange R/O |
| info.version | TEXT | R/O | StringRange R/O |
| info.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| config.slot | CHOICE | SAVE SETUP | EnumRange (01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16) |
| voltage.01 | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| voltage.02 | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| location | CHOICE | EnumRange (1 2) | |
| position | CHOICE | EnumRange (A B) | |
| protection | CHOICE | EnumRange (ON OFF) | |
| number.amp | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| amp.01.bias | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| amp.02.bias | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| amp.03.bias | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| amp.04.bias | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| number.attn | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| attn.01 | FLOAT | DoubleRange (0.0 .. 8.0) | |
| attn.02 | FLOAT | DoubleRange (0.0 .. 0.0) | |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Card status) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 1) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 2) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 3) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Amplifier 4) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Attenuator 1) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Attenuator 2) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Protection) |