User Manual

9.310 Janitza-UMG604

This page describes the device driver and the device window for the Janitza UMG604 line voltage monitor.

Device window pages

The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .

--- The first page shows the actual meter readings of the device. Displayed are voltage, current, power and the consumed energy for each of the three phases L1/L2/L3. Power and energy are shown as a total value es well. Current, power and energy readings refer to the active current.
--- The second page lets you define min / max limits for the voltage readings for all three phases. If a voltage exceeds a limit, a fault is raised and a red light beside the voltage reading at the readings page goes on.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.

Configuration parameters

The only setup parameter which is required to operate line voltage monitor, is the IP address of the device.

Remarks

The voltage limits checked by the device driver are checked in the sat-nms software only. These limits do not have any relation to the limit / transient checking in the UMG604 itself.
There is no way to reset the energy counters in the UMG604 from the sat-nms software.

Variables defined by this device driver

name	type	flags	range
info.driver	TEXT	R/O	StringRange R/O
lowLevel.cmd	TEXT		StringRange
lowLevel.reply	TEXT	R/O	StringRange R/O
faults.99	ALARM	R/O	AlarmFlagRange R/O (Communication)
faults.commstat	TEXT	R/O	StringRange R/O
info.type	TEXT	R/O	StringRange R/O
info.port	TEXT	R/O	StringRange R/O
info.frame	TEXT	R/O	StringRange R/O
info.sysName	TEXT	R/O	StringRange R/O
info.sysDescr	TEXT	R/O	StringRange R/O
uL1N	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
uL2N	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
uL3N	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
iL1	FLOAT	R/O	DoubleRange R/O (0.000 .. 0.000)
iL2	FLOAT	R/O	DoubleRange R/O (0.000 .. 0.000)
iL3	FLOAT	R/O	DoubleRange R/O (0.000 .. 0.000)
pL1	FLOAT	R/O	DoubleRange R/O (0 .. 0)
pL2	FLOAT	R/O	DoubleRange R/O (0 .. 0)
pL3	FLOAT	R/O	DoubleRange R/O (0 .. 0)
pTotal	FLOAT	R/O	DoubleRange R/O (0 .. 0)
internal.p	FLOAT	R/O	DoubleRange R/O (0 .. 0)
eL1	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
eL2	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
eL3	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
eTotal	FLOAT	R/O	DoubleRange R/O (0.0 .. 0.0)
uL1LowLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
uL2LowLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
uL3LowLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
uL1HighLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
uL2HighLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
uL3HighLimit	FLOAT	SAVE	DoubleRange (0.0 .. 400.0)
faults.01	ALARM	R/O	AlarmFlagRange R/O (L1 voltage low limit)
faults.02	ALARM	R/O	AlarmFlagRange R/O (L1 voltage high limit)
faults.03	ALARM	R/O	AlarmFlagRange R/O (L2 voltage low limit)
faults.04	ALARM	R/O	AlarmFlagRange R/O (L2 voltage high limit)
faults.05	ALARM	R/O	AlarmFlagRange R/O (L3 voltage low limit)
faults.06	ALARM	R/O	AlarmFlagRange R/O (L3 voltage high limit)