--- The transmit parameters
--- The meter readings
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for the Miteq Test Loop Translator with synthesizeable LO frequency DN9700 series via Miteq-MOD95.
It was tested with:
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- The transmit parameters --- The meter readings --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the unit.
| parameter | description |
|---|---|
| address | The device address (decimal) as set at the device's front panel. |
| powerDisplayMode | Defines the display of gain or attenuation in the parameter section. |
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.name | TEXT | R/O | StringRange R/O |
| info.version | TEXT | R/O | StringRange R/O |
| info.ifFrequency | CHOICE | R/O | EnumRange R/O (70MHz 140MHz) |
| info.voltageP.15.3 | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.voltageA.5.3 | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.voltageB.5.3 | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.voltageN.15.3 | FLOAT | R/O | DoubleRange R/O (0.00 .. 0.00) |
| info.extRef | CHOICE | R/O | EnumRange R/O (INTERNAL EXTERNAL) |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.gain | INTEGER | IntegerRange (0 .. 30) | |
| tx.attn | INTEGER | IntegerRange (0 .. 30) | |
| lo.frequency | FLOAT | DoubleRange (0.000000 .. 0.000000) | |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Remote access) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Test) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Logged alarm) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (LO) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Power Supply) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Redundancy Bus) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Redundancy switch) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (External) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (TX OFF) |