--- Port switching.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for a Novotronik Matrix MAS5514 . The RX matrix section switches and distributes RF signals from 12 sources (inputs) to 8 receivers (outputs), the TX matrix section switches and combines RF signals from 8 sources (inputs) to 8 receivers (outputs).
Device window pages
The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .
--- Port switching. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
The MAS5321 do not need any configuration parameters except the settings for the serial interface
| parameter | description |
|---|---|
| Serial | Remember to set the line parameters for the serial interface connected to the device. The recommended line setting for the use with the sat-nms software is 9600,N,8,1 . |
Remote Control
RS485/422 uses Novotronik-ASCII protocol
RS232 uses Novotronik protocol
TCP uses Terminal LF protocol
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| output.01 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.02 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.03 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.04 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.05 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.06 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.07 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| output.08 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08) | |
| input.01 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.02 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.03 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.04 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.05 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.06 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.07 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| input.08 | CHOICE | EnumRange (00 01 02 03 04 05 06 07 08 09 10 11 12) | |
| info.swVersion | TEXT | R/O | StringRange R/O |
| info.swDate | TEXT | R/O | StringRange R/O |
| info.serialNo | TEXT | R/O | StringRange R/O |
| info.model | TEXT | R/O | StringRange R/O |
| info.unitInfo | TEXT | R/O | StringRange R/O |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Internal communication) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (Red controller board) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Power supply 1 +5V) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Power supply 2 +5V) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Power supply 1 +9V) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (Power supply 2 +9V) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Manual ctrl module) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (RX input 1..4) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (RX input 5..8) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (RX input 9..12) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (RX 8x8 board 1) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (RX 8x8 board 2) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (RX output 1..4) |
| faults.14 | ALARM | R/O | AlarmFlagRange R/O (RX output 5..8) |
| faults.15 | ALARM | R/O | AlarmFlagRange R/O (TX input 1..4) |
| faults.16 | ALARM | R/O | AlarmFlagRange R/O (TX input 5..8) |
| faults.17 | ALARM | R/O | AlarmFlagRange R/O (TX 8x8 board 1) |
| faults.18 | ALARM | R/O | AlarmFlagRange R/O (TX output 1..4) |
| faults.19 | ALARM | R/O | AlarmFlagRange R/O (TX output 5..8) |
| reset | TEXT | NOPRESET | StringRange |