9.669 Tandberg-RX1290-SNMP

This page describes the device driver and the device window for Tandberg RX1290 DVB-S2 / HDTV IRD, controlled via SNMP.

Device window pages

The following table shows which device window pages are available with this individual device type. Tool-bar functions not mentioned here are described at the general description of device windows .

Configuration parameters

At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the RX1290.

parameter description
address Enter the IP address of the IRD here, in 'dotted quad' notation. The IRD requires the community string 'private' to be appended to the address. Example 10.0.0.1 private
lbandInputs This parameter should be set to the number of L-band input the IRD is equipped with (1/2/4).
22kHz Makes the IRD apply a 22 kHz tone to the LNB power when set to ON.
22kHzAuto If set to ON, the driver switches the 22 kHz tone depending on the receive frequency. Frequencies above the 'bandEdge' value cause the 22kHz tone to be switched on, lower frequencies switch the tone off. The 22kHzAuto mode overwrites the the '22kHz' setting described above.
lnbPower Selects if the IRD shall apply LNB power to the input.
lnbVoltage Selects the LNB power supply voltage (13V/18V). This switches the polarization (13V=Vertical) with some LNBs.
lnbPolSwitch If you set this parameter to ON, the 'lnbVoltage' parameter above becomes read-only and the LNB voltage is controlled though the 'polarization' parameter of the device driver (only makes sense with lnbPower=ON).
lnbBoost Raises the LNB supply voltage by 1V if set to ON (long cable compensation).
loFreqHigh The LO frequency for the high frequency band. The software sets the appropriate LO frequency every time before it changes the receive frequency.
loFreqLow The LO frequency for the low frequency band. The software sets the appropriate LO frequency every time before it changes the receive frequency.
bandEdge The frequency where the software switches the LO frequencies.
spectrumSense Controls the spectrum inversion setting of the IRD. AUTO should work in most cases (switches to NORMAL for Ku-band LO Frequencies, INVERTED for C-band frequencies).
serviceHunt If set to ON, the IRD receives the first available program in a stream when tuned to a new signal. With OFF, the IRD insists in receiving the service ID / PIDs which were set before. For SNG hub applications you will usually select ON, for distribution / relaying applications OFF.
deviceComment An optional text entered here appears as an addition to the tooltip which is shown while the mouse is placed over a device icon in the GUI. The "\n" character sequence is translated into a newline character, splitting the text into multiple lines.

Variables defined by this device driver

name type flags range
info.driver TEXT R/O StringRange R/O
lowLevel.cmd TEXT StringRange
lowLevel.reply TEXT R/O StringRange R/O
faults.99 ALARM R/O AlarmFlagRange R/O (Communication)
faults.commstat TEXT R/O StringRange R/O
info.type TEXT R/O StringRange R/O
info.port TEXT R/O StringRange R/O
info.frame TEXT R/O StringRange R/O
info.inputcard TEXT R/O StringRange R/O
config.readBackDelay INTEGER SAVE SETUP IntegerRange (100 .. 10000)
config.setDelay FLOAT SAVE SETUP DoubleRange (0.0 .. 3.0)
config.lbandInputs CHOICE SAVE SETUP EnumRange (1 2 4)
config.22kHz CHOICE SETUP EnumRange (OFF ON)
config.22kHzAuto CHOICE SAVE SETUP EnumRange (OFF ON)
config.lnbPower CHOICE SETUP EnumRange (OFF ON)
config.lnbVoltage CHOICE SETUP EnumRange (13V 18V)
config.lnbPolSwitch CHOICE SAVE SETUP EnumRange (OFF ON)
config.loFreqHigh INTEGER SAVE SETUP IntegerRange (0 .. 0)
config.loFreqLow INTEGER SAVE SETUP IntegerRange (0 .. 0)
config.bandEdge INTEGER SAVE SETUP IntegerRange (0 .. 0)
config.spectrumSense CHOICE SETUP EnumRange (AUTO NORMAL INVERTED)
config.serviceHunt CHOICE SETUP EnumRange (OFF ON)
config.marginThreshold FLOAT SAVE SETUP DoubleRange (0.00 .. 0.00)
config.deviceComment TEXT SAVE SETUP StringRange
internal.band TEXT R/O StringRange R/O
internal.dummy TEXT R/O StringRange R/O
internal.ix INTEGER R/O IntegerRange R/O (0 .. 0)
internal.dvbs2 INTEGER R/O IntegerRange R/O (0 .. 0)
input CHOICE EnumRange (1 2 3 4)
dvbmode CHOICE EnumRange DIS (DVBS DVBS2)
frequency FLOAT DoubleRange (0.0 .. 0.0)
dataRate FLOAT R/O DoubleRange R/O (0.000 .. 0.000)
symbolRate FLOAT DoubleRange (0.000 .. 0.000)
modulation CHOICE R/O EnumRange R/O (AUTO)
fec CHOICE R/O EnumRange R/O (NONE 1/2 2/3 3/4 5/6 6/7 7/8 8/9 AUTO 1/4 1/3 2/5 3/5 4/5 9/10)
searchRange INTEGER IntegerRange (0 .. 5000)
polarization CHOICE EnumRange (X Y)
rolloff CHOICE EnumRange DIS (35% 25% 20%)
programNo INTEGER IntegerRange (0 .. 65535)
programList CHOICE EnumRange (NO SERVICES)
audioList TEXT R/O StringRange R/O
actualProgram TEXT R/O StringRange R/O
output.tsOutput CHOICE EnumRange (DISABLED POST INPUT POST TS DESCRAMBLE POST ES DESCRAMBLE)
output.conn1 CHOICE EnumRange (DISABLED ASI SD-SDI HD-SDI AUTO)
output.conn2 CHOICE EnumRange (DISABLED ASI SD-SDI HD-SDI AUTO)
output.conn3 CHOICE EnumRange (DISABLED ASI SD-SDI HD-SDI AUTO)
video.pid INTEGER R/O IntegerRange R/O (0 .. 8191)
video.pcrpid INTEGER R/O IntegerRange R/O (0 .. 8191)
video.test CHOICE EnumRange (OFF BARS MOVINGBAR BORDER FULLBARS PATHOLOGICAL MULTIBURST LINEUP CONTRAST)
video.testStandard CHOICE EnumRange (AUTO 1080i 30Hz 1080i 29.97Hz 1080i 25Hz 1080i 24Hz 1080i 23.976Hz 720p 60Hz 720p 59.94Hz 720p 50Hz 480i 29.97Hz 576i 25Hz)
video.input CHOICE EnumRange (ASI SAT)
video.fail CHOICE EnumRange (FREEZE BLACK NO SYNC BLUE BARS BLUE+TXT RED+TXT)
video.framesync CHOICE EnumRange (OFF ON)
video.mode CHOICE EnumRange (PAL-625 NTSC-525)
video.625mode CHOICE EnumRange (PAL-BGI PAL-N PAL-NCMB)
video.525mode CHOICE EnumRange (NTSC-M PAL-M PAL-525)
video.aspect CHOICE EnumRange (4/3 16/9)
video.trisync CHOICE EnumRange (ON ALL ON G/Y NONE)
video.rgbOutput CHOICE EnumRange (RGB YPbPr)
video.embeddedAudio1 CHOICE EnumRange (GROUP1 GROUP2 GROUP3 GROUP4 NONE)
video.embeddedAudio2 CHOICE EnumRange (GROUP1 GROUP2 GROUP3 GROUP4 NONE)
video.embeddedAudio3 CHOICE EnumRange (GROUP1 GROUP2 GROUP3 GROUP4 NONE)
video.embeddedAudio4 CHOICE EnumRange (GROUP1 GROUP2 GROUP3 GROUP4 NONE)
video.standard TEXT R/O StringRange R/O
video.colorType TEXT R/O StringRange R/O
audio.1.program INTEGER IntegerRange (0 .. 8191)
audio.1.routing CHOICE EnumRange (STEREO MONO LEFT RIGHT)
audio.1.output CHOICE EnumRange (AES AC3)
audio.1.level INTEGER IntegerRange (12 .. 24)
audio.1.ac3mix CHOICE EnumRange (SURROUND STEREO)
audio.1.delay INTEGER IntegerRange (-49 .. 49)
audio.1.running BOOLEAN R/O BooleanRange R/O (true false)
audio.2.program INTEGER IntegerRange (0 .. 8191)
audio.2.routing CHOICE EnumRange (STEREO MONO LEFT RIGHT)
audio.2.output CHOICE EnumRange (AES AC3)
audio.2.level INTEGER IntegerRange (12 .. 24)
audio.2.ac3mix CHOICE EnumRange (SURROUND STEREO)
audio.2.delay INTEGER IntegerRange (-49 .. 49)
audio.2.running BOOLEAN R/O BooleanRange R/O (true false)
audio.3.program INTEGER IntegerRange (0 .. 8191)
audio.3.routing CHOICE EnumRange (STEREO MONO LEFT RIGHT)
audio.3.output CHOICE EnumRange (AES AC3)
audio.3.level INTEGER IntegerRange (12 .. 24)
audio.3.ac3mix CHOICE EnumRange (SURROUND STEREO)
audio.3.delay INTEGER IntegerRange (-49 .. 49)
audio.3.running BOOLEAN R/O BooleanRange R/O (true false)
audio.4.program INTEGER IntegerRange (0 .. 8191)
audio.4.routing CHOICE EnumRange (STEREO MONO LEFT RIGHT)
audio.4.output CHOICE EnumRange (AES AC3)
audio.4.level INTEGER IntegerRange (12 .. 24)
audio.4.ac3mix CHOICE EnumRange (SURROUND STEREO)
audio.4.delay INTEGER IntegerRange (-49 .. 49)
audio.4.running BOOLEAN R/O BooleanRange R/O (true false)
flags.lock BOOLEAN R/O BooleanRange R/O (true false)
flags.video BOOLEAN R/O BooleanRange R/O (true false)
flags.audio BOOLEAN R/O BooleanRange R/O (true false)
flags.ts BOOLEAN R/O BooleanRange R/O (true false)
state.ber TEXT R/O StringRange R/O
state.ebno FLOAT R/O DoubleRange R/O (0.00 .. 0.00)
state.margin FLOAT R/O DoubleRange R/O (0.00 .. 0.00)
state.level INTEGER R/O IntegerRange R/O DIS (0 .. 0)
state.plen INTEGER R/O IntegerRange R/O (0 .. 0)
ca.bissmode CHOICE EnumRange (BISS-1 E-FIXED E-TTV E-USER1 E-USER2)
ca.rasmode CHOICE EnumRange (FIXED DSNG)
ca.bisskey TEXT StringRange
ca.raskey INTEGER IntegerRange (0 .. 0)
faults.01 ALARM R/O AlarmFlagRange R/O (Input signal)
faults.02 ALARM R/O AlarmFlagRange R/O (Video)
faults.03 ALARM R/O AlarmFlagRange R/O (Audio)
faults.30 ALARM R/O AlarmFlagRange R/O (Margin)