--- The control parameters
--- The meter readings
--- The redundancy parameters.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for the Work Microwave SCU/HCU upconverter series with one channel.
Device window pages
The following table shows which device window pages are available with this individual device type.
--- The control parameters --- The meter readings --- The redundancy parameters. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the upconverter.
| parameter | description |
|---|---|
| address | The device address (decimal) as set at the device's front panel. |
| Serial | Remember to set the line parameters for the serial interface |
| powerDisplayMode | Defines the display of gain or attenuation in the parameter section. |
| extMuteInput | Defines to disable or enable the input for Hardware Mute (RF-Inhibit). |
| extRef | Defines the reference source. |
| autoSave | Store current parameters automatically in the instrument startup configuration. |
| band | Defines the used frequency band and sets the corresponding rx frequency range: S: 2000 - 2300MHz, C: 5850 - 6650MHz, C1: 5850 - 7200MHz, X: 7900 - 8400MHz, X3: 7000 - 9000MHz, KU: 12750 - 14500MHz, KU2: 11800 - 13400MHz, K: 17300 - 18400MHz. |
| hasEqualizer | Defines if the unit is equipped with an equalizer. |
Remote Control
Default TCP Port= 50505
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.serial | TEXT | R/O | StringRange R/O |
| info.version | TEXT | R/O | StringRange R/O |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| config.readBackDelay | INTEGER | SAVE SETUP | IntegerRange (100 .. 10000) |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| config.extRef | CHOICE | SETUP | EnumRange (INTERNAL EXTERNAL AUTO) |
| config.extMuteInput | CHOICE | SETUP | EnumRange (ENABLED DISABLED) |
| config.autoSave | CHOICE | SETUP | EnumRange (OFF ON) |
| config.band | CHOICE | SAVE SETUP | EnumRange (S C C1 X X3 KU KU2 K) |
| config.hasEqualizer | CHOICE | SAVE SETUP | EnumRange (NO YES) |
| config.accessMode | CHOICE | SAVE SETUP | EnumRange (FULL CONTROL BLOCKED BY RSCM) |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.gain | FLOAT | DoubleRange (0.0 .. 30.0) | |
| tx.attn | FLOAT | DoubleRange (0.0 .. 30.0) | |
| tx.frequency | FLOAT | DoubleRange (12750.0000 .. 14500.0000) | |
| tx.eq | INTEGER | IntegerRange DIS (-64 .. 64) | |
| meas.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.extRef | BOOLEAN | R/O | BooleanRange R/O (true false) |
| meas.extMute | BOOLEAN | R/O | BooleanRange R/O (true false) |
| reset | TEXT | StringRange | |
| internal.sa0 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Remote access) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (OCXO oven cold) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Reference PLL) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (PLO) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (MW PLL) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (VHF Synthesizer) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (FSY Synthesizer) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (Converter comm) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (TX Off) |