--- The operational parameters
--- The redundancy switching parametersThis page describes the device driver and the device window for the Work Microwave Synthesized block upconverters SSBU.
Device window pages
The following table shows which device window pages are available with this individual device type.
--- The operational parameters --- The redundancy switching parametersConfiguration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the upconverter.
| parameter | description |
|---|---|
| address | The device address (decimal) as set at the device's front panel. |
| Serial | Remember to set the line parameters for the serial interface |
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| info.version | TEXT | R/O | StringRange R/O |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| config.extMuteInput | CHOICE | SETUP | EnumRange (ENABLED DISABLED) |
| config.extRef | CHOICE | SETUP | EnumRange (INTERNAL EXTERNAL AUTO) |
| config.autoSave | CHOICE | SETUP | EnumRange (OFF ON) |
| config.bandSelect | CHOICE | SETUP | EnumRange (BAND-1 BAND-2) |
| config.accessMode | CHOICE | SAVE SETUP | EnumRange (FULL CONTROL BLOCKED BY RSCM) |
| config.hasEqualizer | CHOICE | SAVE SETUP | EnumRange (NO YES) |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.gain | FLOAT | DoubleRange (0.0 .. 30.0) | |
| tx.attn | FLOAT | DoubleRange (0.0 .. 30.0) | |
| tx.frequency | FLOAT | DoubleRange (0.000 .. 0.000) | |
| tx.eq | FLOAT | DoubleRange DIS (0.0 .. 8.0) | |
| meas.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.extRef | BOOLEAN | R/O | BooleanRange R/O (true false) |
| meas.extMute | BOOLEAN | R/O | BooleanRange R/O (true false) |
| reset | TEXT | StringRange | |
| internal.sa0 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Remote access) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (OCXO oven cold) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Reference) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Amplifier) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (MW output) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Synthesizer) |
| faults.08 | ALARM | R/O | AlarmFlagRange R/O (Block synthesizer) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (TX Off) |