--- The transmit parameters
--- The meter readings.
--- The redundancy parameters.
--- The faults page.
--- The device info page.
--- The maintenance page. The configuration parameters described below are set at this page.This page describes the device driver and the device window for the Work Microwave Test Loop Translator.
The driver was tested with the following models:
VHTLT-Ku-OD-RIN-S0078
VSTLT-X-S00306
Device window pages
The following table shows which device window pages are available with this individual device type.
--- The transmit parameters --- The meter readings. --- The redundancy parameters. --- The faults page. --- The device info page. --- The maintenance page. The configuration parameters described below are set at this page.Configuration parameters
At the maintenance page of the device window there are a couple of configuration parameters which must be set to make the software talk to the unit.
| parameter | description |
|---|---|
| address | The device address (decimal) as set at the device's front panel. |
| Serial | Remember to set the line parameters for the serial interface |
| powerDisplayMode | Defines the display of gain or attenuation in the parameter section. |
| extMuteInput | Defines to disable or enable the input for Hardware Mute (RF-Inhibit). |
| extRef | Defines the reference source. |
| autoSave | Store current parameters automatically in the instrument startup configuration. |
| adjLO | Defines the usage of a individual transmit frequency. |
Remote Control
Default TCP Port= 50505
Variables defined by this device driver
| name | type | flags | range |
|---|---|---|---|
| info.driver | TEXT | R/O | StringRange R/O |
| lowLevel.cmd | TEXT | StringRange | |
| lowLevel.reply | TEXT | R/O | StringRange R/O |
| faults.99 | ALARM | R/O | AlarmFlagRange R/O (Communication) |
| faults.commstat | TEXT | R/O | StringRange R/O |
| info.type | TEXT | R/O | StringRange R/O |
| info.port | TEXT | R/O | StringRange R/O |
| info.frame | TEXT | R/O | StringRange R/O |
| config.powerDisplayMode | CHOICE | SAVE SETUP | EnumRange (GAIN ATTN) |
| config.extMuteInput | CHOICE | SETUP | EnumRange (ENABLED DISABLED) |
| config.extRef | CHOICE | SETUP | EnumRange (INTERNAL EXTERNAL AUTO) |
| config.autoSave | CHOICE | SETUP | EnumRange (OFF ON) |
| config.adjLO | CHOICE | SAVE SETUP | EnumRange (1 2) |
| config.accessMode | CHOICE | SAVE SETUP | EnumRange (FULL CONTROL BLOCKED BY RSCM) |
| config.rxBand | CHOICE | SAVE SETUP | EnumRange (NONE S C C1 X KU KU1 K KA1 KA) |
| config.txBand | CHOICE | SAVE SETUP | EnumRange (NONE S C C1 X KU KU1 K KA1 KA) |
| config.deviceComment | TEXT | SAVE SETUP | StringRange |
| info.serial | TEXT | R/O | StringRange R/O |
| info.FrontBaseVersion | TEXT | R/O | StringRange R/O |
| info.FrontDeviceVersion | TEXT | R/O | StringRange R/O |
| info.InterfaceVersion | TEXT | R/O | StringRange R/O |
| info.ReferenceVersion | TEXT | R/O | StringRange R/O |
| info.SynthesizerVersion | TEXT | R/O | StringRange R/O |
| tx.on | CHOICE | EnumRange (OFF ON) | |
| tx.gain | FLOAT | DoubleRange (0.0 .. 30.0) | |
| tx.attn | FLOAT | DoubleRange (0.0 .. 30.0) | |
| rx.frequency | FLOAT | DoubleRange (0.0000 .. 0.0000) | |
| tx.frequency | FLOAT | DoubleRange DIS (0.0000 .. 0.0000) | |
| meas.temperature | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| meas.extRef | BOOLEAN | R/O | BooleanRange R/O (true false) |
| meas.extMute | BOOLEAN | R/O | BooleanRange R/O (true false) |
| info.temp.frontpanel | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.temp.controller | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.temp.refBoard | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.temp.synthesizer | FLOAT | R/O | DoubleRange R/O (0.0 .. 0.0) |
| info.signal.on | CHOICE | R/O | EnumRange R/O (OFF ON) |
| reset | TEXT | StringRange | |
| internal.sa0 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| internal.sa1 | INTEGER | R/O | IntegerRange R/O (0 .. 0) |
| faults.01 | ALARM | R/O | AlarmFlagRange R/O (Remote access) |
| faults.02 | ALARM | R/O | AlarmFlagRange R/O (OCXO oven cold) |
| faults.03 | ALARM | R/O | AlarmFlagRange R/O (Internal alarm) |
| faults.04 | ALARM | R/O | AlarmFlagRange R/O (Reference PLL alarm) |
| faults.05 | ALARM | R/O | AlarmFlagRange R/O (Amplifier alarm) |
| faults.06 | ALARM | R/O | AlarmFlagRange R/O (MW output alarm) |
| faults.07 | ALARM | R/O | AlarmFlagRange R/O (Synthesizer alarm) |
| faults.09 | ALARM | R/O | AlarmFlagRange R/O (External mute) |
| faults.10 | ALARM | R/O | AlarmFlagRange R/O (External mute input) |
| faults.11 | ALARM | R/O | AlarmFlagRange R/O (EEPROM) |
| faults.12 | ALARM | R/O | AlarmFlagRange R/O (Temperature high) |
| faults.13 | ALARM | R/O | AlarmFlagRange R/O (Temperature low) |
| faults.25 | ALARM | R/O | AlarmFlagRange R/O (External Ref) |
| faults.26 | ALARM | R/O | AlarmFlagRange R/O (RX OFF) |