The page 'Setup' contains the sat-nms LFTX/RX installation parameters. Installation parameters are those which are assumed to be changed less frequently than the operational parameters on the configuration page .
The page displays a table with the parameters actually set. Each parameter value is a hyper-link to a separate page which lets you change this parameter. This parameter change page shows the actual parameter setting either in an entry field or in a drop down box. You may change the parameter to the desired value and then click to the 'Submit' button to pass the changed value to the LFTX/RX. The receiver automatically returns to the settings page when the parameter has been changed.
To cancel a parameter modification you already started, either use the 'Back' button of you web browser or click to the 'Config' button on navigation bar. Both returns to the config page without changing the parameter you edited.
The table below lists the settings provided by this page.
| Parameter Name | Description |
|---|---|
| General | |
| Date/ Time | If you want to set the Date and/ or the Time, type the actual Date and Time in the following syntax: YYYY-MM-DD HH:MM:SS It is not possible to change only one of both parameters. |
| Refresh rate | Here you can configure the automatic refresh time for the Master Ch. and the Slave Ch. pages. You can choose between 1s, 3s, 5s and 10s. |
| Chassis Type | Choose here the chassis type "single", "master" or "slave". In case of using the LFTX/RX as "master" or "slave" you have to set additional settings. Please refer to Master/Slave mode parameters . |
| RS232 Baud rate | select here the bit rate for the RS232 Interface. You can choose between 9600, 19200, 38400, 57600, 115200 baud |
| RS232 Address | This parameter defines the communication address to be used with the serial interface. You may select an address 'A' .. 'G' for the packet mode communication protocol or 'NONE' to switch the communication mode to a plain text protocol. |
| Note | Enter here the Name of the LFTX/RX chassis. This name will be displayed on the top of the 'Master Ch.' or 'Slave Ch.' page. In case of using the LFTX/RX in master/slave mode you can change the master's name with the parameter 'Note Master Unit' and the slave's name with the parameter 'Note Slave Unit'. |
| Redundancy Def. | Please refer to the Redundancy parameters . |
| SNMP Configuration | |
| Read Community | Sets the SNMP community string expected for read access. The default is 'public'. |
| Write Community | Sets the SNMP community string expected for write access. The default is 'public'. |
| Trap Community | Sets the SNMP community string sent with traps. The default is 'public'. |
| Trap Destination IP 1 | Enter the trap destination IP address (dotted quad notation) to make the unit sending traps by UDP to this host. Setting the parameter to 0.0.0.0 disables the trap generation. |
| Trap Destination IP 2 | Enter the trap destination IP address (dotted quad notation) to make the unit sending traps by UDP to this host. Setting the parameter to 0.0.0.0 disables the trap generation. |
| Trap Destination IP 3 | Enter the trap destination IP address (dotted quad notation) to make the unit sending traps by UDP to this host. Setting the parameter to 0.0.0.0 disables the trap generation. |
| Trap Destination IP 4 | Enter the trap destination IP address (dotted quad notation) to make the unit sending traps by UDP to this host. Setting the parameter to 0.0.0.0 disables the trap generation. |
| System Location | The unit replies to MIB-II sysLocation requests with the text entered at this place. |
| System Contact | The unit replies to MIB-II sysContact requests with the text entered at this place. |
| IP-Setting | |
| IP-Address | Enter the Unit IP address (dotted quad notation). Remark: IP Re-Config. ETH needs to be applied to set IP address. |
| IP-Subnetmask | Enter the Unit IP subnetmask (dotted quad notation). Remark: IP Re-Config. ETH needs to be applied to set networkmask. |
| IP-Gateway | Enter the Unit IP dateway (dotted quad notation). Remark: IP Re-Config. ETH needs to be applied to set gateway. |
| IP Re-Config. ETH | Enter apply to set the Unit network parameter. Enter cancel to reload actual unit settings. |
| Access Control | |
| User password | Here you can define the password for the 'user' login. Default password is 'user'. When you are logged in as 'user' you are only able to change the parameters on the 'Master Ch.' And the 'Slave Ch.' page. All the other parameters can only be changed when you are logged in as 'admin' |
| Admin password | Here you can define the password for the 'admin' login. Default password is 'admin'. When you are logged in as "admin" you are only able to change all the parameters of the unit. |