sat-nms LFTX/RX User Manual

Version 2.0.008 -- 2024-06-18 -- © 2011-2024 SatService GmbH

Abstract

This document is the user manual provided with the sat-nms LFTX/RX fibre optical link equipment. It contains all necessary information how to install, setup, and operate the unit. The user manual is available as a printed document and for on-line reading on the optical links itself as well.

Table Of Contents

• 1 Introduction
  • 1.1 Compliances
    • 1.1.1 CE Compliances
      • 1.1.1.1 EMC compliance
      • 1.1.1.2 Federal Communications Commission (FCC)
    • 1.1.2 Safety compliance
• 2 Installation
  • 2.1 Safety Instructions
  • 2.2 Handling instructions for optical connectors
  • 2.3 Setting the IP Address
  • 2.4 Mechanical installation
  • 2.5 Connecting the sat-nms LFTX/RX
    • 2.5.1 Optical receiver and transmitter cards
    • 2.5.2 Power connectors and power supplies
    • 2.5.3 DC and data connectors
    • 2.5.4 RF connectors
    • 2.5.5 Optical connectors
    • 2.5.6 optional relay alarm interface
    • 2.5.7 optional 75Ohm converter
    • 2.5.8 optional 1:4 splitter 'LFRXv4'
    • 2.5.9 optional dual coupler 'LFC10TX' and 'LFC10RX'
  • 2.6 Configuring the Optical Links
  • 2.7 Line-up the Optical Links
• 3 Operation
  • 3.1 The Web-based User Interface
  • 3.2 Display Readings
    • 3.2.1 Reading of LFRX receiver card
    • 3.2.2 Reading of LFTX transmitter card
    • 3.2.3 Reading of empty slots
  • 3.3 Configuration of operational parameters
    • 3.3.1 Configuration of LFRX receiver card
    • 3.3.2 Configuration of LFTX transmitter card
    • 3.3.3 Empty slots
  • 3.4 General Setup
    • 3.4.1 Master/Slave mode parameters
    • 3.4.2 Redundancy parameters
    • 3.4.3 Configuring master/slave mode
    • 3.4.4 Real Time Clock battery backup
  • 3.5 Front panel Operation
    • 3.5.1 Display Mode
    • 3.5.2 The Main Menu
    • 3.5.3 Editing Numeric Parameters
    • 3.5.4 Editing Multiple Choice Parameters
    • 3.5.5 Fault Display
    • 3.5.6 Local operation LFRX Card
    • 3.5.7 Local operation LFTX Card
• 4 Remote Control
  • 4.1 General command syntax
  • 4.2 The TCP/IP remote control interface
  • 4.3 The RS232 remote control interface
  • 4.4 SNMP Control
  • 4.5 Parameter list
• 5 Theory of Operation
  • 5.1 Frequency bands
  • 5.2 Connectors
  • 5.3 Controller Module
  • 5.4 Redundancy switching
    • 5.4.1 none Redundancy (none)
    • 5.4.2 2 x n:1 Redundancy(n=1..4) (intern, intern2)
    • 5.4.3 2 x n:1 Redundancy(n=1..4) (extern, extern2)
    • 5.4.4 5 x 1:1 Redundancy (int1to1)
  • 5.5 Level-Diagram
  • 5.6 Outline Drawing
• 6 Specifications
  • 6.1 RF Specification
  • 6.2 M&C Interface Specification
  • 6.3 Electrical and Mechanical Specification, Environmental Conditions